American Bass Godfather Horn Driver 2"/3" Coil Options

American Bass Godfather Horn Driver 2"/3" Coil Options

Sold by AudioSellerz.com

The American Bass Godfather Horn Driver is built for loud car audio systems that need sharp high-frequency projection, strong upper-range output, and the kind of volume that can keep up with aggressive mids, midbass, and subwoofer setups.

This is a car audio horn driver / compression driver for mids-and-highs systems. It is not a factory replacement speaker and it is not a vehicle warning horn. It is made for custom doors, speaker pods, demo vehicles, loud daily systems, and builds where the highs need to cut through clearly.

This listing gives you 2" coil and 3" coil options, making it a serious choice for customers building louder speaker sections around American Bass Godfather equipment.

Need to finish the rest of the speaker setup?
shop American Bass car audio products | shop car audio horns | shop tweeters | shop 4-channel amplifiers

Why Choose the American Bass Godfather Horn Driver?

The Godfather Horn Driver is for customers who need the high-frequency side of the system to stay loud, clear, and aggressive. If the bass and mids are strong but the highs disappear when the system gets turned up, a properly powered and crossed-over horn driver can help bring the top end back into the build.

This horn driver is a good fit for systems that need:

• Louder highs and upper-range projection
• Strong output for mids-and-highs builds
• A horn driver that can keep up with loud midrange speakers
• A high-sensitivity driver for demo vehicles and loud daily systems
• A serious speaker option for custom doors, pods, and panels
• A stronger high-frequency section to balance upgraded subwoofers

Product Highlights

• American Bass Godfather Series horn driver
• 2" coil and 3" coil options
• High-output car audio compression driver design
• Designed for loud highs and upper-frequency projection
• Useful for custom doors, pods, demo vehicles, and mids-and-highs builds
• Good match for loud American Bass speaker setups
• Requires proper amplifier matching and crossover protection

Verified 2" Coil Specification Details

• Brand: American Bass
• Series: Godfather
• Product type: Horn driver / compression driver
• Model: GF-HORN-2 / Godfather HO-2V
• Exit throat diameter: 2"
• Nominal impedance: 8 ohm
• Rated power handling: 100 watts
• Program power: 450 watts
• Sensitivity: 108dB
• Voice coil diameter: 2"
• Voice coil wire: CCAW
• Voice coil former material: Aluminum
• Diaphragm material: Titanium
• Magnet material: Ceramic
• Overall diameter: 6.10"
• Front mount baffle cutout: 5.74"
• Mounting depth: 4.82"
• Overall depth: 5.14"

Important Note About Coil Options

This product is shown with 2" coil and 3" coil options. The verified specification details above are for the 2" coil version. If you choose the 3" coil option, confirm the exact box label, impedance, mounting information, and power rating before building or cutting anything.

Because horn drivers are easy to damage when crossed too low or overpowered with dirty signal, always match the selected coil option with the right amplifier, crossover point, speaker count, and final impedance.

Built for Loud High-Frequency Output

In a loud car audio system, the highs can get buried fast if the speaker section is not planned correctly. Big subwoofers, strong midbass, and aggressive midrange speakers can overpower weak tweeters or factory-style speakers.

The American Bass Godfather Horn Driver helps add stronger upper-range output so vocals, instruments, cymbals, and detail can stay present when the system gets loud.

Good Fit For

• Custom car audio door builds
• Speaker pod installs
• Loud mids-and-highs systems
• Demo vehicles
• Show builds
• Loud daily-driver systems
• American Bass speaker builds
• Systems that need stronger highs to keep up with bass and mids

Use the Right Amplifier

This horn driver should be matched with clean amplifier power and proper crossover controls. Do not buy a high-output horn driver like this just to run it from weak factory radio power.

Match the amplifier by RMS power, impedance, number of drivers, final channel load, crossover control, and the goal of the system. Clean power and correct tuning matter more than chasing max power numbers.

Shop matching install parts here:
shop car audio amplifiers | shop 4-channel amplifiers for speakers | shop amplifier wiring kits | shop car audio wire

Crossover Protection Matters

Horn drivers are not midbass speakers and they are not subwoofers. They should not be sent deep bass, low midbass, or uncontrolled full-range signal. Use the proper high-pass crossover, clean gain settings, and amplifier power to help protect the driver.

The listed frequency range for the 2" version is 1KHz–18KHz, so the system should be planned around proper high-frequency use. Midbass speakers should handle punch, midrange speakers should handle vocals and instruments, and horn drivers should handle the upper-range output they are designed for.

Helpful guides:
read the full range vs midrange vs midbass vs tweeter guide | read the car audio speaker tuning guide | read the amp gain setting guide

Plan the Full Speaker System

A horn driver works best when the whole speaker setup is planned together. The subwoofers, midbass drivers, midrange speakers, tweeters, horn drivers, amplifier channels, crossover points, and speaker locations all need to make sense together.

If the build uses loud subwoofers and multiple midrange speakers, the high-frequency section needs enough output to keep up without being harsh, distorted, or poorly protected.

Check Fitment Before Ordering

Before ordering, confirm the selected coil option, horn driver size, mounting depth, cutout size, pod design, door clearance, baffle strength, wiring path, amplifier setup, and crossover plan.

The verified 2" version lists a 5.74" front mount baffle cutout and 4.82" mounting depth. Always measure the exact install location before cutting doors, panels, pods, or brackets.

Not a Vehicle Safety Horn

This is a car audio horn driver / compression driver. It is not a replacement for your vehicle’s factory warning horn, air horn, or safety horn. It is made for the speaker side of a car audio system.

Frequently Asked Questions

Is this a car audio speaker horn?

Yes. This is a car audio horn driver / compression driver for loud speaker systems, not a vehicle safety horn.

Does this listing have 2" and 3" coil options?

Yes. The listing shows 2" coil and 3" coil options.

Is the 2" version 8 ohm?

The verified 2" specification sheet lists the Godfather HO-2V as 8 ohm.

How much power does the 2" version handle?

The verified 2" specification sheet lists 100 watts rated power handling and 450 watts program power.

Can I run this from a factory radio?

No. A horn driver like this should be used with a properly matched amplifier, correct crossover protection, and clean tuning.

Do I need a crossover?

Yes. A proper high-pass crossover is required. Do not send horn drivers low frequencies or uncontrolled full-range signal.

Can this be used with midrange and midbass speakers?

Yes. Horn drivers are commonly used as part of a louder mids-and-highs setup with midrange and midbass speakers, but the full system needs proper crossover planning and amplifier matching.

Why Buy American Bass From Audio Sellerz?

Audio Sellerz is a real car audio shop that works with daily builds, custom doors, speaker pods, demo vehicles, subwoofer systems, mids-and-highs setups, wiring, electrical upgrades, and complete system planning.

If you are not sure if the American Bass Godfather Horn Driver is the right match for your build, message us through the live chat bubble on AudioSellerz.com and we can help you match horn drivers, midrange speakers, amplifiers, wiring, and crossover needs.

Want more help planning the full system?
read how to pick the right car audio system

Follow Audio Sellerz

Follow Audio Sellerz for car audio products, installs, demos, speaker upgrades, wiring tips, and new product updates:
Facebook | Instagram | TikTok | YouTube