ANL

ANL Fuses & ANL Fuse Holders for Car Audio

Sold by AudioSellerz.com

Shop ANL fuses and ANL fuse holders for amplifier power wire, Big 3 upgrades, extra batteries and high-output alternator systems. This collection includes ceramic ANL fuses from 100A up to 600A, single ANL fuse holders, set-screw holders made for 1/0 gauge wire, and ANL distribution holders that split one big power run into several fused outputs.

If the main fuse on your power wire is weak, loose or the wrong size, nothing else in the system is protected the way it should be. ANL is one of the most common fuse styles in car audio for that reason. It bolts down tight, handles serious current and is easy to find in the sizes car audio systems actually use.

Shop Fuse Blocks | Shop Distribution Blocks | Shop 0 Gauge Wire | Shop Amp Kits

What Is an ANL Fuse?

An ANL fuse is a bolt-down fuse with a flat body and a mounting hole on each end. Instead of sliding into clips like an old glass fuse, it bolts onto studs inside the fuse holder. That gives you a solid connection that does not wiggle loose over time, which matters when a lot of current is moving through it.

ANL fuses are used on:

  • Main amplifier power wire near the battery
  • Cables running between a front battery and rear batteries
  • Big 3 and charging wire upgrades
  • High-output alternator charge wire
  • Fused distribution for multiple amplifiers

What the ANL Fuse Is Really Protecting

The fuse near the battery is there to protect the power wire. If that wire ever gets cut, pinched or rubbed through and touches the body of the vehicle, the fuse needs to blow before the wire overheats. That is the whole job.

That is why the fuse should be matched to the wire you are running and the system it feeds. A fuse that is too large for the wire can let the wire overheat before the fuse ever blows. Our car audio wire gauge chart and fuse guide walks through how wire size and fuse size go together.

Where to Mount an ANL Fuse Holder

Mount the main ANL fuse holder on the positive wire as close to the battery as you can. Many amplifier manufacturers and installers call for the fuse to be within about 18" of the battery, and closer is better. The less unfused wire you have, the less wire is unprotected.

A few things that make the install last:

  • Mount the holder to something solid so it cannot bounce around
  • Keep the cover on so nothing metal can bridge the terminals
  • Keep it away from moving parts and hot exhaust components
  • Tighten the nuts or set screws and check them again after the wire settles
  • If a cable runs between two batteries, fuse it near each battery

Choosing the Right ANL Fuse Size

There is no single ANL size that is right for every car. Start with three things:

  • The wire. Size and type matter. OFC and CCA wire of the same gauge do not carry current the same way.
  • The amplifier. Check what fuse size the amplifier manufacturer recommends.
  • The layout. One amp on one run is simple. Multiple amps usually means one main fuse at the battery and smaller fuses on each branch.

If a fuse keeps blowing, do not just put a bigger one in. Find out why. A loose ground, a pinched wire or an amp pulling more than the wiring was planned for are all common causes.

Need wire to match? Browse 1/0 gauge car audio wire, 4 gauge wire or read our OFC vs CCA wire size guide.

Ceramic ANL Fuses

Many of the ANL fuses in this collection use a ceramic body, including the B2 Audio high temperature ceramic ANL fuses and the Reactor ceramic ANL fuses from DC Audio. Ceramic bodied fuses are built to handle the heat that comes with high current systems that get played hard for long periods.

Shop options like the Reactor ceramic ANL fuse (100A to 600A) or the B2 Audio ceramic ANL fuse pairs in 150A, 250A, 300A and 500A.

Types of ANL Fuse Holders

Standard ANL Fuse Holders

One wire in, one wire out. Square and round ANL fuse holders are the simple way to protect a single power run. Some come with the fuse included so you can install it right away.

Set-Screw ANL Fuse Holders

A set-screw ANL fuse holder clamps the bare wire with set screws, so you do not need ring terminals. They are popular with 1/0 gauge wire because they make a clean, tight connection. Check out the Sky High Car Audio 1/0 gauge set-screw ANL fuse holder and the Limitless Lithium 1/0 ANL set-screw fuse holder.

ANL Distribution Fuse Holders

An ANL distribution holder takes one large input and splits it into several fused outputs. For example, 1/0 gauge in and three 4 gauge outputs, each with its own ANL fuse. That is a clean way to feed more than one amplifier from a single power run. You can find more options in our car audio distribution blocks collection.

ANL vs Mini ANL

Mini ANL fuses work the same way but are physically smaller and are used for lower current circuits or tight spaces. If you are protecting a smaller amp or a smaller wire run, a mini ANL setup like the Audio Sellerz Economy Mini ANL fuse block may be all you need.

Common ANL Fuse Mistakes

  • Mounting the fuse far away from the battery
  • Using a fuse that is bigger than the wire can safely handle
  • Leaving nuts or set screws loose, which creates heat
  • Running a cable to a rear battery without fusing it
  • Upsizing the fuse to stop it from blowing instead of finding the problem
  • Leaving the fuse holder uncovered

Why Buy ANL Fuses From Audio Sellerz?

Audio Sellerz is run by real car audio people who build, install and play high power systems every day. We work with amp wiring, battery banks, Big 3 upgrades and high output alternators all the time, so we know how much the small parts like fuses and fuse holders matter.

Not sure what size you need? Use the live chat on AudioSellerz.com and tell us your amp, wire size and battery setup.

ANL Fuse FAQ

What does ANL stand for?

ANL is the name of the fuse style. In car audio it simply refers to the bolt-down fuse with a mounting hole on each end that is used for high current power wire.

What is an ANL fuse used for in car audio?

It protects the main power wire running from the battery to the amplifiers, and it is also used on battery to battery cables, Big 3 wiring and alternator charge wire.

How close to the battery should an ANL fuse be?

As close as you can practically mount it. Many manufacturers call for within about 18" of the battery.

What size ANL fuse do I need?

It depends on the wire size, wire type and what the amplifier manufacturer recommends. The fuse should never be larger than what the wire can safely carry.

Are ceramic ANL fuses better?

Ceramic bodied ANL fuses are built to handle heat well, which makes them a popular choice in systems that get played hard. Size still matters more than body style.

Do I need a fuse on both ends of a battery cable?

If the cable runs between two batteries, both ends can supply current, so fusing near each battery is the common practice.

What is the difference between ANL and mini ANL?

Mini ANL fuses are smaller and used for lower current circuits. Standard ANL fuses are used for larger power wire and higher current.

Why does my ANL fuse keep blowing?

Common causes include a short in the power wire, a bad ground, a fuse that is too small for the system or an amplifier pulling more current than planned. Find the cause before going up in size.

Shop More Car Audio Electrical

Big 3 Kits | Lithium Car Audio Batteries | High Output Alternators | Car Audio Wire

Follow Audio Sellerz

Follow Audio Sellerz for electrical upgrades, amp installs, battery builds and new car audio products:

Facebook | Instagram | TikTok | YouTube